Power Tool Guide – Best Tips That Will Help You Use Your Cordless Drill Easily And Safely!

Power Tool Guide – Best Tips That Will Help You Use Your Cordless Drill Easily And Safely!

- in Home Improvement
114
Comments Off on Power Tool Guide – Best Tips That Will Help You Use Your Cordless Drill Easily And Safely!

Using power tools can make even the toughest job easy and quick. However, if not used properly, they can even make the simplest of tasks dangerous.

When it comes to power tool safety, most of the people just consider the concerns involved in working with blades and saws. They mostly overlook the fact that even some of the smaller tools should be handled with caution since carelessness while handling it may cause serious injuries and accidents.

Therefore, understanding some of the basic as well as advanced safety tips when operating power tools including cordless drills can not only extent life of tools, but also greatly impact your personal safety. No matter whether you are a new drill user or an expert, the following safety tips will help you greatly.

Wear work gloves and safety goggles

Power grills most of the times give off serious vibrations, especially on high torque. They can even reach high temperature due to friction and impact. Wearing thick gloves can help you handle the tool safely. It will even help you to prevent contact with hot surface while loosening the chuck or changing drill bits.

While operating power drill, some of the small materials from target surface can fly off in the surrounding space. If any such particle happens to enter your eyes, it may be sometimes very difficult to remove. It can even cause discomfort and pain. So, wearing sturdy safety goggles will ultimately protect your eyes.

Moreover, it is also very important to wear thick protective clothing while using power drill. Avoid long clothing that may get entangled in work surface. Moreover, it is advised to avoid wearing any kind of jewelry and keep the long hair out of the way.

Is the chuck tight?

Chuck is restraining mechanism holding the drills in place. A power drill may have either a key-less or keyed chuck. As its name suggests, a keyed chuck requires special key to turn chuck and tighten it properly in place. On the other hand, key-less chuck can easily be tightened by hand.

Once the drilling job is accomplished, make sure to unplug the drill, loosen chuck, and then remove drill bit before you fit a new drill tip or bit. A loose chuck can sometimes be dangerous since it won’t hold drill bit in proper place. In case, drill bit is undone and flies off in middle of the job, it may cause great danger to people surrounding it.

Moreover, make sure to turn off the switch and unplug the power cord after every drilling job. Never ever change the drill bits when power cord is connected to power supply. Make sure to use safety latch when the drill isn’t in use. Most of the advanced drills have this type of safety feature in them. You can get more information about it just by visiting http://www.nuttydiy.com/.

Few important Do’s and Don’ts to remember when operating a cordless drill

  • Before using the power drill, ensure to read safety section well of the drill’s instruction manual. It will help you know in what conditions and temperatures your drill can be safe to use.
  • Look before you start to drill. When drilling into a ceiling or floor, inspect the area carefully for live electrical wires. It may involve going into the attic or house to scout location of building’s wiring. If you are working in the older structure, make sure to have it inspected well.
  • Avoid wearing clothing that totally covers your hands. Loose fabric may become snagged in rotating equipment that can ultimately cause serious injuries in the arms.
  • Be wary of the hot drill bits. Avoid laying the drill down especially where the children, pets or any other workers may brush up against hot bit.
  • Check out for the product recalls that involves the brand of your cordless drill periodically. Some of the models may have been recalled due to melting, smoking, or even fires. Plus, check your drill regularly for melted, broken, and loose parts.
  • Clamp your project to table or any other stable work area securely to avoid your hands from getting close to bit.
  • Ensure to keep your drills dry. While the drill has low enough voltage, operating it in wet conditions can damage it and cause dangerous slipping on the work surface.
  • Don’t run or walk with your fingers on trigger.
  • Don’t ever use a cordless drill having damaged or loose parts.
  • Don’t mix and match the chargers and drills.

When operating a drill, safety always starts with proper techniques. Following the above tips and by using top quality drills, you can be rest assured about their safety along with their effectiveness.